A bit of summer maintenance

For all those techno questions

A bit of summer maintenance

Postby Suff » 19 Jul 2016, 19:02

It seems my antenna for PC issues is clogged at the moment.

I've noticed for a while that my PC was spinning it's fan long and often. I'd also noticed that the response times were a bit slower than usual, part of which I put down to the Windows 10 upgrade I've just done.

Until I came home tonight and found the room boiling (opened the windows) and the machine off.

When I started the machine it took a long time to get going and, eventually, started spinning the fan fast again. So I went and found some diagnostics software which would tell me how hot everything was. It told me my CPU was sitting at around 61C. Now that's not that far off normal ( normal is mid 50's), but still hotter than I would have expected with the fan going so fast.

So I powered it down, lifted the bottom off it and had a look at the fans. A quick spin of the fans showed me that all 3 were moving fine (usual problem is they jam). Putting my hand over the board, though, elicits some seriously hot space over the CPU fan.

I undid the fan and lifted it out. To find the heatsink vent fins almost completely blocked with fluff and gunk. Out with the Vacuum, off with all 3 fans, hovered and blew it totally clean and Voila.

Machine is going like a bat out of hell. Faster than when I first built it clean with W7 nearly 5 years ago. Web pages are startlingly fast and everything is as it should be. God knows how long it's been throttling itself but I'm glad it's back to it's normal self.

When I set out to spend nearly £4,000 I told Mrs S that I wanted a machine I could install the latest operating system on, 5 years down the line and have it run at least as fast as when I bought it.

I've exceeded my expectations and that is really something else. It's not as fast, it's way faster. Windows 10 with good hardware goes like a rocket. OK so I have very fast graphics in it for a "normal" machine, but then I don't play games on it.

It's always useful to get the case off and look for dust every now and then. I should have done this years ago. The fan is almost silent and the whole machine is cool. This might also explain all the network dropouts I've been having. The network adapter is right over the top of the cpu heatsink and was at least 60c.
There are 10 types of people in the world:
Those who understand Binary and those who do not.
User avatar
Suff
 
Posts: 10785
Joined: 26 Nov 2012, 08:35

Re: A bit of summer maintenance

Postby Workingman » 20 Jul 2016, 09:53

Did my laptop about this time last year - similar problems.

When I took the base off, the fan blades looked as though they were made of felt and there was a forest of unknown gunk sitting on the main board. The air vents looked ok from the outside, but inside they all had beards. :roll:

I took the vacuum hose and an artist's paint brush to it, remembering first to put a hankie over the open suction end. I have sucked all sorts of essential things up in the past and it is no fun going through the vac's dust canister with a toothpick.

It really is quite amazing what a bit of housekeeping can do.

BTW did you use new paste on the heat-sink/CPU joint? It's another Lazarus trick that does wonders for a few pence.
User avatar
Workingman
 
Posts: 21743
Joined: 26 Nov 2012, 15:20

Re: A bit of summer maintenance

Postby Suff » 20 Jul 2016, 11:29

No I left it in place. The fins are on the end of a heat tube and the fan is totally separate from the CPU. Makes maintaining it much easier as the CPU is buried in the middle of the board and under The top of the case which would mean a full strip.
There are 10 types of people in the world:
Those who understand Binary and those who do not.
User avatar
Suff
 
Posts: 10785
Joined: 26 Nov 2012, 08:35

Re: A bit of summer maintenance

Postby Workingman » 20 Jul 2016, 15:17

Yes, sometimes things are best left alone.

I discovered, by accident, that the paste worked on some camping gear. I have three boxes, two for cooling and one for heating. After three weeks in a dusty S of France they were pretty useless, so once home I would strip them and clean them. They were OK, but not the best.

One year a Peltier unit fell apart and I thought that was it.... then I remembered the paste. A quick clean and a splodge of paste and the thing was almost better than new. It became the annual post holiday task.

I often wonder when I see these things at the recycling centre, some of them pretty new, how many could be brought back to life for mere pennies.
User avatar
Workingman
 
Posts: 21743
Joined: 26 Nov 2012, 15:20

Re: A bit of summer maintenance

Postby Suff » 20 Jul 2016, 19:59

Workingman wrote:I often wonder when I see these things at the recycling centre, some of them pretty new, how many could be brought back to life for mere pennies.


Yes a consumer society doesn't do that does it.....
There are 10 types of people in the world:
Those who understand Binary and those who do not.
User avatar
Suff
 
Posts: 10785
Joined: 26 Nov 2012, 08:35


Return to Computers etc

Who is online

Users browsing this forum: No registered users and 83 guests